We're only interested in card devices. The loop over wlr_session.devices
would take care of ignoring non-card events, but a future patch will
listen to udev "add" events as well.
Instead of operating on FDs in {open,close}_device, operate on
wlr_devices. This avoids the device lookup in wlr_session and allows
callers to have access to wlr_device fields.
For now, we use it to remove wlr_session_signal_add and replace it with
a more idiomatic wlr_session.events.change field. In the future, other
events will be added.
We would always return the GAMMA_LUT_SIZE property if available, and
only fall back to legacy gamma size otherwise. This leads to issues if
both are available in differs in size while we use the legacy backend.
Ensure that we only return the legacy size if we're using the legacy
backend.
Closes: https://github.com/swaywm/wlroots/issues/2429
We have the policy of requiring up-to-date dependencies instead of
adding conditionals for older versions. libinput 1.14 was published more
than 1 year ago.
Every host seat with pointer capability propagates events to one of
sub-pointer depending which output window we entered.
active_pointer tracks reference to sub-pointer on enter/leave events to
avoid lookup for it on every move events.
Fixesswaywm/wlroots#1499
This effectively gets swaywm/wlroots#1499 to the point where
functionality somewhat preserved and no crash happens.
We still can have only one cursor, but we can control it from multiple
seats in time-sharing manner by entering/leaving output.
When performing a modeset, the DRM backend will request a page-flip
event. However frame_pending wasn't set to true, so any subsequent
wlr_output_schedule_frame calls would imemdiately trigger a synthetic
frame event, asking the compositor to submit a new frame. Committing the
new frame fails with "a page-flip is already pending" error in the DRM
backend.
When an output is disabled one last pageflip will happen to disable it.
Currently this pageflip causes a frame event.
Since the output is disabled we don't want to send this frame event.
I'm not sure what this was used for, but it's not used by libwayland.
Setting _WAYLAND_DISPLAY would result in the Wayland backend being
picked but would ignore the actual value of the env variable.
When starting a compositor that's using the "direct" session backend,
wlroots needs to handle calls to `drmSetMaster()` and `drmDropMaster()`.
As both calls used to require `CAP_SYS_ADMIN`, wlroots thus simply
refused starting in case the process doesn't enjoy evelated privileges.
Permission rules have changed since linux.git commit 45bc3d26c95a (drm:
rework SET_MASTER and DROP_MASTER perm handling, 2020-03-19). As a
result, starting with Linux v5.8, both ioctls will now also succeed if
the process is currently or has been the DRM master. And as the first
process to open render nodes will become the DRM master automatically,
this effectively means that process elevation is not strictly required
in all setups anymore.
So let's drop the `geteuid() != 0` permission check to allow those new
rules to do their magic.
bad1e9afa8 ("session: Add libseat backend") introduced a change to to
how session backends initialize, but failed to update the FreeBSD
specific version of the direct backend accordingly.
Closes: https://github.com/swaywm/wlroots/issues/2376
get_drm_prop_blob does not set path_len if it returns NULL. Check the
return value before path_len to avoid reading uninitialized memory.
(Granted, this doesn't change the logic at all, but it does make
Valgrind a bit happier.)
drm_connector_set_cursor wasn't checking the return value of the
drm_surface_make_current call. On failure, this results in a failed
assertion in wlr_renderer_begin (because no rendering context is
current).
The output backend API is now mostly state-less thanks to the atomic
hooks (commit and test). There is one exception though: attach_render.
This function makes the rendering context current. However sometimes the
compositor might decide not to render after attach_render (e.g. when
there's nothing new to render to the back buffer). Thus
wlr_output_rollback has been introduced to revert the pending state.
Because the output backend API is mostly state-less, the only thing
wlr_output_impl.rollback needs to do is revert the current rendering
context. Rename the function to rollback_render to make this clear. Add
a check in the common wlr_output code to only call rollback_render when
attach_buffer has been previously called.
On the long term, we'll be able to remove attach_render and
rollback_render together.
This commit makes `get_current_time_msec` correctly return milliseconds
as opposed to microseconds. It also considers the value of `tv_sec`, so
we don't lose occasionally go back in time by one second. Finally, the
function is moved into `util/time.cc` so that it can be reused elsewhere
without having to consider these pitfalls.
This patch fixes this failure:
01:57:16.642 [ERROR] [backend/drm/drm.c:360] Failed to page-flip output 'eDP-1': a page-flip is already pending
01:57:16.684 [ERROR] [backend/drm/drm.c:360] Failed to page-flip output 'eDP-1': a page-flip is already pending
01:57:16.684 [ERROR] [backend/drm/drm.c:732] Failed to initialize renderer on connector 'eDP-1': initial page-flip failed
01:57:16.684 [ERROR] [backend/drm/drm.c:805] Failed to initialize renderer for plane
01:57:16.684 [sway/config/output.c:423] Failed to commit output eDP-1
References: https://github.com/swaywm/sway/issues/5101
When the mode, status or buffer hasn't changed, drm_connector_commit was
a no-op. Because of this individual changes to the gamma LUT or adaptive
sync status were ignored (if committed without a buffer).
Instead, perform a commit to apply the changes.
A test commit doesn't apply the pending state.
The CRTC state will be populated again if the compositor decides to
perform a regular commit afterwards.
Previously, we only had the pending state (crtc->pending, crtc->mode and
crtc->active). This causes issues when a commit fails: the pending state
is left as-is, and the next commit may read stale data from it.
This will also cause issues when implementing test-only commits: we need
to rollback the pending CRTC state after a test-only commit.
Introduce separate pending and current CRTC states. Properly update the
current state after a commit.
retry_pageflip is now dead code, since drm_connector_start_renderer
isn't called anymore. It was previously called when enabling an output.
The name "retry_pageflip" was a little confusing because the function
retried a modeset and the timer wasn't set up while performing a simple
page-flip.
Let's just remove this altogether for now. We can discuss whether it's
worth it to bring it back. Should we only do it on failed page-flips?
Should we only do it on EBUSY?
If the atomic commit fails or is test-only, rollback
wlr_drm_crtc.{mode_id,gamma_lut} blob IDs to their previous value. This
prevents the next commits from failing or applying test-only state.
After swapping buffers, it doesn't make sense to perform more rendering
operations. Unset the context to reflect this.
This commit makes it so the context is always only current between
wlr_egl_make_current and wlr_egl_swap_buffers.
This is an alternative to [1].
[1]: https://github.com/swaywm/wlroots/pull/2212
This function can be called after wlr_egl_make_current to cleanup the
EGL context. This avoids having lingering EGL contexts that make things
work by chance.
Closes: https://github.com/swaywm/wlroots/issues/2197
When calling assert(0) instead of returning a value, -Wreturn-type
warnings are triggered because assertions can be disabled. Replace these
assertions with abort().
We already have the logic to fallback to the legacy interface above. We
just need to avoid calling atomic_add with a zero prop ID.
Closes: https://github.com/swaywm/wlroots/issues/2187
dealloc_crtc was destroying GBM surfaces, but the cursor_enabled flag
was left as-is. When re-enabling the output, atomic_crtc_pageflip would
try enabling the cursor plane, but would fail because no framebuffer is
available.
Closes: https://github.com/swaywm/wlroots/issues/2150
When an output is enabled and modeset at the same time,
drm_connector_commit would first try to modeset then try to commit. This
won't work because both will trigger a page-flip. KMS will reject that.
Change the logic to only enable an output if no modeset has been
requested. The logic in wlr_output already checks that the user isn't
doing a modeset and disabling the output at the same time.
We have a workaround for legacy drivers that support drmModeSetCursor
without exposing a cursor plane. It doesn't work anymore now that we've
moved to a more atomic interface.
Let's just remove this workaround and fallback to software cursors.
Closes: https://github.com/swaywm/wlroots/issues/2166
conn->crtc is NULL in case the output is disabled.
However, the DRM backend will set the GAMMA_LUT property anyway. On each
commit the whole state is sent to KMS. Adding WLR_DRM_CRTC_GAMMA_LUT to
the pending state would just make the backend re-create the blob
containing the gamma LUT.
We don't need a per-CRTC atomic request anymore. Let's make the request
per-commit so that it's easier to debug.
This is also groundwork for supporting wlr_output_test properly.
GAMMA_LUT_SIZE isn't an atomic property. It can be used with the legacy
interface too. So we can unify both codepaths and remove
wlr_drm_interface.crtc_get_gamma_size.
It's no guaranteed to exist though, so we still need to keep the
fallback.
When the headless backend uses an already-existing renderer, it doesn't
have ownership over the renderer. When the renderer is destroyed, the
headless backend needs to destroy itself.
The logs don't currently display the importance of a line. It's easy to
read "skipping page-flip" as a debug message instead of an error
message.
Change the error message to make it more explicit.
References: https://github.com/swaywm/wlroots/pull/2147
