Custom backends and renderers need to implement
wlr_backend_impl.get_buffer_caps and
wlr_renderer_impl.get_render_buffer_caps. They can't if enum
wlr_buffer_cap isn't made public.
Right now, when a new output state field is added, all backends by
default won't reject it. This means we need to add new checks to
each and every backend when we introduce a new state field.
Instead, introduce a bitmask of supported output state fields in
each backend, and error out if the user has submitted an unknown
field.
Some fields don't need any backend involvment to work. These are
listed in WLR_OUTPUT_STATE_BACKEND_OPTIONAL as a convenience.
The set_cursor() hook is a little bit special: it's not really
synchronized to commit() or test(). Once set_cursor() returns true,
the new cursor is part of the current state.
This fixes a state where wlr_drm_connector.cursor_enabled is true
but there is no FB available. This is triggered by set_cursor()
followed by a failed commit(), which resets pending_fb.
We should definitely fix the output interface to make the cursor part
of the pending state, but that's a more involved change.
Instead of trying to perform a real modeset in init_renderer,
perform an atomic test-only commit to find out whether disabling
modifiers is necessary because of bandwidth limitations.
This decouples init_renderer from the actual commit, making it
possible to modeset an output with a user-supplied buffer instead
of a black frame.
We loose the ability to make sure the buffers coming from the
swapchain will work fine when using the legacy interface. This
can break i915 when atomic is disabled and modifiers enabled.
But i915 always has atomic (so the user must explicitly disable it
to run into potential bandwidth limitations) and is the only known
problematic driver.
Instead of passing a wlr_texture to the backend, directly pass a
wlr_buffer. Use get_cursor_size and get_cursor_formats to create
a wlr_buffer that can be used as a cursor.
We don't want to pass a wlr_texture because we want to remove as
many rendering bits from the backend as possible.
This new functions cleans up the common backend state. While this
currently only emits the destroy signal, this will also clean up
the renderer and allocator in upcoming patches.
Backend-initiated mode changes can use this function instead of
going through drm_connector_set_mode. drm_connector_set_mode becomes
a mere drm_connector_commit_state helper.
Replace it with a new drm_connector_state_is_modeset function that
decides whether a modeset is necessary directly from the
wlr_output_state which is going to be applied.
Populate the wlr_output_state when setting a mode. This will allow
drm_connector_set_mode to stop relying on ephemeral fields in
wlr_drm_crtc. Also drm_connector_set_mode will be able to apply
both a new buffer and a new mode atomically.
Stop assuming that the state to be applied is in output->pending in
crtc_commit. This will allow us to remove ephemeral fields in
wlr_drm_crtc, which are used scratch fields to stash temporary
per-commit data.
On multi-GPU setups, there is a primary DRM backend and secondary
DRM backends. wlr_backend_get_drm_fd will always return the parent
DRM FD even on secondary backends, so that users always use the
primary device for rendering.
However, for our internal rendering we want to use the secondary
device. Use allocator_autocreate_with_drm_fd to make sure the
allocator will create buffers on the secondary device.
We do something similar to ensure our internal rendering will
happen on the secondary device with renderer_autocreate_with_drm_fd.
Fixes: cc1b66364c ("backend: use wlr_allocator_autocreate")
This function is only required because the DRM backend still needs
to perform multi-GPU magic under-the-hood. Remove the wlr_ prefix
to make it clear it's not a candidate for being made public.
This reverts commit f9f90b4173.
gbm_bo_get_modifier may return a modifier in these cases:
- The kernel doesn't support modifiers but Mesa does
- WLR_DRM_NO_MODIFIERS=1 is set
However, in both of these cases, the gbm_bo has been allocated
without modifiers.
There is already a check in drm_fb_create for modifiers:
wlr_drm_format_set_has will make sure buffers with an explicit
modifier will be rejected if the DRM backend doesn't support them.
So no need for an additional check in get_fb_for_bo.
Closes: https://github.com/swaywm/wlroots/issues/2896
The previous code would always print "falling back to legacy method",
even if the format wasn't ARGB8888.
Drop get_fb_for_bo_legacy, since the code can just be inlined without
hurting readability.
Ideally we should only fallback to drmModeAddFB if the error code
indicates the BE failure, but the original PR [1] doesn't say what
error code is returned by the kernel.
[1]: https://github.com/swaywm/wlroots/pull/2569
We shouldn't strip a modifiers from buffers, because the will make
the kernel re-interpret the data as LINEAR on most drivers,
resulting in an incorrect output on screen.
PRIME support for buffer sharing has become mandatory since the renderer
rewrite. Make sure we check for the appropriate capabilities in backend,
allocator and renderer.
See also #2819.
Downgrade errors to DEBUG level, because drm_fb_create is used in
test_buffer, so errors aren't always fatal. Add ERROR logs at call
sites where a failure is fatal, to make it clear something wrong
happened.
If the import to KMS succeeds, we have a better chance to be able to
scan it out.
Importing is also necessary for test-only commits, which we want to
add in the future.
Compute only the transform matrix in the output. The projection matrix
will be calculated inside the gles2 renderer when we start rendering.
The goal is to help the pixman rendering process.
In 93cd3a79b2 ("backend/drm: stop using GBM flags"), we stopped
using the GBM_BO_USE_LINEAR flag in favor of a modifier list set
to { DRM_FORMAT_MOD_LINEAR }. However, the last argument of
drm_plane_init_surface disables modifiers -- so the buffer will just
get allocated with an implicit modifier, without necessarily being
LINEAR.
To fix this, allow modifiers when allocating the cursor buffers.
wlr_drm_plane.formats should already have the necessary LINEAR
restrictions.
Fixes: 93cd3a79b2 ("backend/drm: stop using GBM flags")
This allows a compositor to get a KMS connector object ID from a
wlr_output. The compositor can then query more information about
the connector via libdrm.
This gives more freedom to compositors and allows them to read
KMS properties that wlroots doesn't know about. For instance,
they could read the EDID or the suggested_{X,Y} properties and
change their output configuration based on that.
The subconnector property indicates the connector sub-type. This is
useful because that usually indicates what kind of connector the user
has plugged in to their monitor, e.g. a DisplayPort-to-DVI cable will
indicate a DVI subconnector. Also some laptops have non-DP connectors
that are internally linked to a DP port on the GPU.
Set the output description accordingly.
See https://drmdb.emersion.fr/properties/3233857728/subconnector
The new wlr_renderer_autocreate API is great for compositors, however
it causes some issues with DRM multi-GPU support.
A DRM child backend wants the compositor to use the parent GPU, so it
exposes the parent's DRM FD in get_drm_fd. However, in order to be able
to perform multi-GPU buffer copies, the child DRM backend still needs to
create a local renderer.
Use the new private wlr_renderer_autocreate_with_drm_fd function to
avoid creating a renderer for the parent GPU.
Fixes: e128e6c08d ("render: drop egl parameters from wlr_renderer_autocreate")
Instead of requiring callers to manually make the EGL context current
before binding a buffer and unsetting it after unbinding a buffer, do
it inside wlr_renderer_bind_buffer.
This hides renderer-specific implementation details inside the
wlr_renderer interface. Non-GLES2 renderers may not use EGL.
This removes all EGL dependencies from the backends.
References: https://github.com/swaywm/wlroots/issues/2618
References: https://github.com/swaywm/wlroots/pull/2615#issuecomment-756687006
Since 5b1b43c68c ("backend/drm: make wlr_drm_plane.{pending,queued,current}_fb
pointers"), current_fb can be NULL if there's no buffer. If current_fb
is not NULL, current_fb->wlr_buf is guaranteed to not be NULL.
Closes: https://github.com/swaywm/wlroots/issues/2634
Stop using wlr_drm_surface.{width,height} to figure out the size of a
gbm_bo. In the future we'll stop using wlr_drm_plane.surf, so these will
be zero. Instead, rely on gbm_bo_get_{width,height}.
Stop keeping track of buffers on the parent GPU when multi-GPU is used.
This removes support for export_dmabuf on secondary GPUs, but renderer
v6 will bring this back by managing the swapchains in wlr_output instead
of the backends.
wlr_drm_connector.crtc may be updated by the DRM backend while a
page-flip is pending. In this case, the page-flip handler won't be able
to find the right wlr_drm_connector from the CRTC ID.
Save the CRTC when performing a page-flip to ensure we always find the
right connector when we get the event.
When the session is inactive, we can't change the KMS state. Ignore
hotplug events so that compositors don't try to perform a modeset when
a connector is plugged in. We already re-scan connectors when the
session becomes active.
To test, run a wlroots compositor on VT 1, switch to VT 2, unplug a
connector, re-plug it, switch back to VT 1. Without this patch the
screen is black on VT 1.
References: https://github.com/swaywm/wlroots/issues/2370
This callback allowed compositors to customize the EGL config used by
the renderer. However with renderer v6 EGL configs aren't used anymore.
Instead, buffers are allocated via GBM and GL FBOs are rendered to. So
customizing the EGL config is a no-op.
We now properly mark the cursor plane's formats as linear-only, and we
now have a version of wlr_drm_format_intersect that handles the case of
linear-only formats and implicit modifiers.
We can remove the special drm_plane_init_surface flag we had for cursor
planes. This also allows us to use a non-linear layout for cursor planes
on drivers that support it.
Tested on amdgpu GFX9.
If the kernel driver doesn't support modifiers, it still expects cursor
FBs to have a LINEAR layout. See [1] for expectations for framebuffers
attached to the cursor plane.
[1]: https://patchwork.freedesktop.org/patch/408512/
Parse WLR_DRM_NO_MODIFIERS at startup. Don't parse IN_FORMATS when
WLR_DRM_NO_MODIFIERS is set, so that the legacy behaviour is better
reproduced.
When modifiers aren't supported, try the initial page-flip once only.
This was lost during the refactoring. We were previously calling
wlr_output_destroy, which destroyed the connector as well.
Fixes: 248c7787c7 ("backend/drm: refactor wlr_output destruction")
The DRM backend is a little special when it comes to wlr_outputs: the
wlr_drm_connectors are long-lived and are created even when no screen is
connected.
A wlr_drm_connector only advertises a wlr_output to the compositor when
a screen is connected. As such, most of wlr_output's state is invalid
when the connector is disconnected.
We want to stop using wlr_output state on disconnected connectors.
Introduce wlr_drm_connector.name which is always valid regardless of the
connector status to avoid reading wlr_output.name when disconnected.
Simplify and unify connector-specific logging with a new
wlr_drm_conn_log macro. This makes it easier to understand which
connector a failure is about, without having to explicitly integrate the
connector name in each log message.
The workaround is broken because drm_fb_acquire doesn't leave the EGL
context current anymore. We'll need to re-introduce it.
References: https://github.com/swaywm/wlroots/issues/2525
gbm_bo_create_with_modifiers doesn't take GBM flags, so our
wlr_gbm_allocator interface doesn't either. We were still internally
using GBM flags in the DRM backend, leading to awkward back-and-forth
conversions.
The only flag passed to drm_plane_init_surface was GBM_BO_USE_LINEAR, so
turn that into a bool to make sure other flags can't be passed in.
Move the "force linear" logic out of init_drm_surface, because the
supplied wlr_drm_format should already contain that information.
drm_fb_import_wlr may need to change the current EGL context. For
instance by calling drm_fb_clear, which calls wlr_buffer_unlock, which
may destroy a buffer if the cursor swapchain size has changed, which
calls gles2's destroy_buffer, which calls glDeleteFramebuffers.
Closes: https://github.com/swaywm/wlroots/issues/2479
This is just the vendor-agnostic define for the GBM platform. It has the
same value as EGL_PLATFORM_GBM_MESA, so should work with old drivers
that only offer the Mesa-vendored extension too.
On some platforms it's possible that the display engine supports
modifiers not supported by the render engine.
Query render formats and intersect them with plane formats to accommodate
for this.
After discussing with Pekka and Daniel on #dri-devel, we concluded [1]
that user-space shouldn't need to force-probe connectors. Force-probing
can take some time, so using drmModeGetConnectorCurrent can result in
faster start-up.
Users can manually trigger a force-probe if necessary:
echo detect | sudo tee /sys/class/drm/card0-DP-1/status
Or just by running a tool like drm_info.
A similar change has been submitted to Weston [2].
[1]: https://lists.freedesktop.org/archives/dri-devel/2020-November/287728.html
[2]: https://gitlab.freedesktop.org/wayland/weston/-/issues/437
Instead of operating on FDs in {open,close}_device, operate on
wlr_devices. This avoids the device lookup in wlr_session and allows
callers to have access to wlr_device fields.
For now, we use it to remove wlr_session_signal_add and replace it with
a more idiomatic wlr_session.events.change field. In the future, other
events will be added.
We would always return the GAMMA_LUT_SIZE property if available, and
only fall back to legacy gamma size otherwise. This leads to issues if
both are available in differs in size while we use the legacy backend.
Ensure that we only return the legacy size if we're using the legacy
backend.
Closes: https://github.com/swaywm/wlroots/issues/2429
When performing a modeset, the DRM backend will request a page-flip
event. However frame_pending wasn't set to true, so any subsequent
wlr_output_schedule_frame calls would imemdiately trigger a synthetic
frame event, asking the compositor to submit a new frame. Committing the
new frame fails with "a page-flip is already pending" error in the DRM
backend.
When an output is disabled one last pageflip will happen to disable it.
Currently this pageflip causes a frame event.
Since the output is disabled we don't want to send this frame event.
get_drm_prop_blob does not set path_len if it returns NULL. Check the
return value before path_len to avoid reading uninitialized memory.
(Granted, this doesn't change the logic at all, but it does make
Valgrind a bit happier.)
drm_connector_set_cursor wasn't checking the return value of the
drm_surface_make_current call. On failure, this results in a failed
assertion in wlr_renderer_begin (because no rendering context is
current).
The output backend API is now mostly state-less thanks to the atomic
hooks (commit and test). There is one exception though: attach_render.
This function makes the rendering context current. However sometimes the
compositor might decide not to render after attach_render (e.g. when
there's nothing new to render to the back buffer). Thus
wlr_output_rollback has been introduced to revert the pending state.
Because the output backend API is mostly state-less, the only thing
wlr_output_impl.rollback needs to do is revert the current rendering
context. Rename the function to rollback_render to make this clear. Add
a check in the common wlr_output code to only call rollback_render when
attach_buffer has been previously called.
On the long term, we'll be able to remove attach_render and
rollback_render together.
This patch fixes this failure:
01:57:16.642 [ERROR] [backend/drm/drm.c:360] Failed to page-flip output 'eDP-1': a page-flip is already pending
01:57:16.684 [ERROR] [backend/drm/drm.c:360] Failed to page-flip output 'eDP-1': a page-flip is already pending
01:57:16.684 [ERROR] [backend/drm/drm.c:732] Failed to initialize renderer on connector 'eDP-1': initial page-flip failed
01:57:16.684 [ERROR] [backend/drm/drm.c:805] Failed to initialize renderer for plane
01:57:16.684 [sway/config/output.c:423] Failed to commit output eDP-1
References: https://github.com/swaywm/sway/issues/5101
When the mode, status or buffer hasn't changed, drm_connector_commit was
a no-op. Because of this individual changes to the gamma LUT or adaptive
sync status were ignored (if committed without a buffer).
Instead, perform a commit to apply the changes.
A test commit doesn't apply the pending state.
The CRTC state will be populated again if the compositor decides to
perform a regular commit afterwards.
Previously, we only had the pending state (crtc->pending, crtc->mode and
crtc->active). This causes issues when a commit fails: the pending state
is left as-is, and the next commit may read stale data from it.
This will also cause issues when implementing test-only commits: we need
to rollback the pending CRTC state after a test-only commit.
Introduce separate pending and current CRTC states. Properly update the
current state after a commit.
retry_pageflip is now dead code, since drm_connector_start_renderer
isn't called anymore. It was previously called when enabling an output.
The name "retry_pageflip" was a little confusing because the function
retried a modeset and the timer wasn't set up while performing a simple
page-flip.
Let's just remove this altogether for now. We can discuss whether it's
worth it to bring it back. Should we only do it on failed page-flips?
Should we only do it on EBUSY?
If the atomic commit fails or is test-only, rollback
wlr_drm_crtc.{mode_id,gamma_lut} blob IDs to their previous value. This
prevents the next commits from failing or applying test-only state.
After swapping buffers, it doesn't make sense to perform more rendering
operations. Unset the context to reflect this.
This commit makes it so the context is always only current between
wlr_egl_make_current and wlr_egl_swap_buffers.
This is an alternative to [1].
[1]: https://github.com/swaywm/wlroots/pull/2212
This function can be called after wlr_egl_make_current to cleanup the
EGL context. This avoids having lingering EGL contexts that make things
work by chance.
Closes: https://github.com/swaywm/wlroots/issues/2197
We already have the logic to fallback to the legacy interface above. We
just need to avoid calling atomic_add with a zero prop ID.
Closes: https://github.com/swaywm/wlroots/issues/2187
dealloc_crtc was destroying GBM surfaces, but the cursor_enabled flag
was left as-is. When re-enabling the output, atomic_crtc_pageflip would
try enabling the cursor plane, but would fail because no framebuffer is
available.
Closes: https://github.com/swaywm/wlroots/issues/2150
When an output is enabled and modeset at the same time,
drm_connector_commit would first try to modeset then try to commit. This
won't work because both will trigger a page-flip. KMS will reject that.
Change the logic to only enable an output if no modeset has been
requested. The logic in wlr_output already checks that the user isn't
doing a modeset and disabling the output at the same time.
We have a workaround for legacy drivers that support drmModeSetCursor
without exposing a cursor plane. It doesn't work anymore now that we've
moved to a more atomic interface.
Let's just remove this workaround and fallback to software cursors.
Closes: https://github.com/swaywm/wlroots/issues/2166
conn->crtc is NULL in case the output is disabled.
However, the DRM backend will set the GAMMA_LUT property anyway. On each
commit the whole state is sent to KMS. Adding WLR_DRM_CRTC_GAMMA_LUT to
the pending state would just make the backend re-create the blob
containing the gamma LUT.
We don't need a per-CRTC atomic request anymore. Let's make the request
per-commit so that it's easier to debug.
This is also groundwork for supporting wlr_output_test properly.
GAMMA_LUT_SIZE isn't an atomic property. It can be used with the legacy
interface too. So we can unify both codepaths and remove
wlr_drm_interface.crtc_get_gamma_size.
It's no guaranteed to exist though, so we still need to keep the
fallback.
The logs don't currently display the importance of a line. It's easy to
read "skipping page-flip" as a debug message instead of an error
message.
Change the error message to make it more explicit.
References: https://github.com/swaywm/wlroots/pull/2147
Reconnecting an external display fails on initial
page-flip. This occurs when the pageflip_pending flag
has been set on the connector at the time the monitor
is removed. Once the connector's CRTC has been deallocated,
page_flip_handler cannot find the connector by its crtc_id,
so pageflip_pending will remain set. This causes
initialization to fail when the monitor is reconnected
with the error messages:
Skipping pageflip on output 'X'
Failed to initialize renderer on connector 'X': initial page-flip failed
To fix this problem, clear the pageflip_pending flag
when cleaning up the connector.
Some primary planes don't support ARGB8888, they only support XRGB8888
(for instance on older Intel hardware). The DRM backend would fail to
initialize.
When that's the case, try to allocate buffers without an alpha channel.
This is a type which manages gbm_surfaces and imported dmabufs in the
same place, and makes the lifetime management between the two shared. It
should lead to easier to understand code, and fewer special cases.
This also contains a fair bit of refactoring to start using this new
type.
Co-authored-by: Simon Ser <contact@emersion.fr>
Most of the pending output state is not forwarded to the backend prior
to an output commit. For instance, wlr_output_set_mode just stashes the
mode without calling any wlr_output_impl function.
wlr_output_impl.commit is responsible for applying the pending mode.
However, there are exceptions to this rule. The first one is
wlr_output_attach_render. It won't go away before renderer v6 is
complete, because it needs to set the current EGL surface.
The second one is wlr_output_attach_buffer.
wlr_output_impl.attach_buffer is removed in [1].
When wlr_output_rollback is called, all pending state is supposed to be
cleared. This works for all the state except the two exceptions
mentionned above. To fix this, introduce wlr_output_impl.rollback.
Right now, the backend resets the current EGL surface. This prevents GL
commands from affecting the output after wlr_output_rollback.
This patch is required for FBO-based outputs to work properly. The
compositor might be using FBOs for its own purposes [2], having leftover
FBO state can have bad consequences.
[1]: https://github.com/swaywm/wlroots/pull/2097
[2]: https://github.com/swaywm/wlroots/pull/2063#issuecomment-597614312
Check that buffer can be scanned out in wlr_output_test instead of
wlr_output_attach_buffer. This allows the backend to have access to the
whole pending state when performing the check.
This brings the wlr_output API more in line with the KMS API.
This removes the need for wlr_output_attach_buffer to return a value,
and for wlr_output_impl.attach_buffer.
Consumers call wlr_buffer_lock. Once all consumers are done with the
buffer, only the producer should have a reference to the buffer. In this
case, we can release the buffer (and let the producer re-use it).
This function allowed backends to provide a custom function for frame
scheduling. Before resuming the rendering loop, the DRM and Wayland
backends would wait for vsync.
There isn't a clear benefit of doing this. The only upside is that we
get more stable timings: the delay between two repaints doesn't change too
much and is close to a mutliple of the refresh rate.
However this introduces latency, especially when a client misses a
frame. For instance a fullscreen game missing vblank will need to wait
more than a whole frame before being able to display new content. This
worst case scenario happens as follows:
- Client is still rendering its frame and cannot submit it in time
- Deadline is reached
- Compositor decides to stop the rendering loop since nothing changed on
screen
- Client finally manages to render its frame, submits it
- Compositor calls wlr_output_schedule_frame
- DRM backend waits for next vblank
- The wlr_output frame event is fired, compositor draws new content on screen
- On the second next vblank, the new content reaches the screen
With this patch, the wlr_output frame event is fired immediately when
the client submits its late frame.
This change also makes it easier to support variable refresh rate, since
VRR is all about being able to present too-late frames earlier.
References: https://github.com/swaywm/wlroots/issues/1925
The previous PR was overzealous in adding a finish_drm_surface call
which was also done by the caller. Remove the call and also move the
comment to the correct code location.
In some cases modesets fail if the planes are initialized with
modifiers. Since in this case possibly all planes need to reinitialized,
which is not possible in the current wlroots design, add an environment
variable for affected users.
This fixes a segfault in drm_connector_set_mode (mode = NULL).
This happens because we set wlr_output.enabled to true if the connector
is attached to the CRTC. When the user disables an output in the
wlroots-based compositor, switches to another VT (enabling the output),
then switches back, wlroots sets wlr_output.enabled to true but
wlr_output.current_mode is NULL.
We should consider not reading properties from KMS after a TTY switch,
disabling all connectors. However this may result in flickering (outputs
being disabled then re-enabled).
Closes: https://github.com/swaywm/wlroots/issues/1874
wlr_output.description is a string containing a human-readable string
identifying the output. Compositors can customise it via
wlr_output_set_description, for instance to make the name more
user-friendly.
References: https://github.com/swaywm/wlroots/issues/1623
Bumps minimum version to 0.51.0
- Remove all intermediate static libraries.
They serve no purpose and are just add a bunch of boilerplate for
managing dependencies and options. It's now managed as a list of
files which are compiled into libwlroots directly.
- Use install_subdir instead of installing headers individually.
I've changed my mind since I did that. Listing them out is annoying as
hell, and it's easy to forget to do it.
- Add not_found_message for all of our optional dependencies that have a
meson option. It gives some hints about what option to pass and what
the optional dependency is for.
- Move all backend subdirectories into their own meson.build. This
keeps some of the backend-specific build logic (especially rdp and
session) more neatly separated off.
- Don't overlink example clients with code they're not using.
This was done by merging the protocol dictionaries and setting some
variables containing the code and client header file.
Example clients now explicitly mention what extension protocols they
want to link to.
- Split compositor example logic from client example logic.
- Minor formatting changes
Remove glapi.sh code generation, replace it with hand-written loading
code that checks extension strings before calling eglGetProcAddress.
The GLES2 renderer still uses global state because of:
- {PUSH,POP}_GLES2_DEBUG macros
- wlr_gles2_texture_from_* taking a wlr_egl instead of the renderer
This fixes a heap-use-after-free when the session is destroyed before
the backend during wl_display_destroy:
==1085==ERROR: AddressSanitizer: heap-use-after-free on address 0x614000000180 at pc 0x7f88e3590c2d bp 0x7ffdc4e33f90 sp 0x7ffdc4e33f80
READ of size 8 at 0x614000000180 thread T0
#0 0x7f88e3590c2c in find_device ../subprojects/wlroots/backend/session/session.c:192
#1 0x7f88e3590e85 in wlr_session_close_file ../subprojects/wlroots/backend/session/session.c:204
#2 0x7f88e357b80c in libinput_close_restricted ../subprojects/wlroots/backend/libinput/backend.c:24
#3 0x7f88e21af274 (/lib64/libinput.so.10+0x28274)
#4 0x7f88e21aff1d (/lib64/libinput.so.10+0x28f1d)
#5 0x7f88e219ddac (/lib64/libinput.so.10+0x16dac)
#6 0x7f88e21b415d in libinput_unref (/lib64/libinput.so.10+0x2d15d)
#7 0x7f88e357c9d6 in backend_destroy ../subprojects/wlroots/backend/libinput/backend.c:130
#8 0x7f88e3545a09 in wlr_backend_destroy ../subprojects/wlroots/backend/backend.c:50
#9 0x7f88e358981a in multi_backend_destroy ../subprojects/wlroots/backend/multi/backend.c:54
#10 0x7f88e358a059 in handle_display_destroy ../subprojects/wlroots/backend/multi/backend.c:107
#11 0x7f88e314acde (/lib64/libwayland-server.so.0+0x8cde)
#12 0x7f88e314b466 in wl_display_destroy (/lib64/libwayland-server.so.0+0x9466)
#13 0x559fefb52385 in main ../main.c:67
#14 0x7f88e2639152 in __libc_start_main (/lib64/libc.so.6+0x27152)
#15 0x559fefb4297d in _start (/home/simon/src/glider/build/glider+0x2297d)
0x614000000180 is located 320 bytes inside of 416-byte region [0x614000000040,0x6140000001e0)
freed by thread T0 here:
#0 0x7f88e3d0a6b0 in __interceptor_free /build/gcc/src/gcc/libsanitizer/asan/asan_malloc_linux.cc:122
#1 0x7f88e35b51fb in logind_session_destroy ../subprojects/wlroots/backend/session/logind.c:270
#2 0x7f88e35905a4 in wlr_session_destroy ../subprojects/wlroots/backend/session/session.c:156
#3 0x7f88e358f440 in handle_display_destroy ../subprojects/wlroots/backend/session/session.c:65
#4 0x7f88e314acde (/lib64/libwayland-server.so.0+0x8cde)
previously allocated by thread T0 here:
#0 0x7f88e3d0acd8 in __interceptor_calloc /build/gcc/src/gcc/libsanitizer/asan/asan_malloc_linux.cc:153
#1 0x7f88e35b911c in logind_session_create ../subprojects/wlroots/backend/session/logind.c:746
#2 0x7f88e358f6b4 in wlr_session_create ../subprojects/wlroots/backend/session/session.c:91
#3 0x559fefb51ea6 in main ../main.c:20
#4 0x7f88e2639152 in __libc_start_main (/lib64/libc.so.6+0x27152)
This requires functions without a prototype definition to be static.
This allows to detect dead code, export less symbols and put shared
functions in headers.
This is set to the value of wlr_output.commit_seq when the frame has
been submitted. This allows tracking presentation with more then 1 full
frame of latency.
References: https://github.com/swaywm/wlroots/issues/1917
Instead of checking that the path property is not 0 to determine if the
connector is an MST connector, check if the path contains the mst:
string.
Fixes#1813
Instead of waiting for the next pageflip, destroy the output immediately
since we can now handle flips for outputs which no longer exist.
Also demote the missing crtc on flip to debug.
Fixes#1739
This commit makes more output properties (mode, enabled, scale and transform)
atomic. This means that they are double-buffered and only applied on commit.
Compositors now need to call wlr_output_commit after setting any of those
properties.
Internally, backends still apply properties sequentially. The behaviour should
be exactly the same as before. Future commits will update some backends to take
advantage of the atomic interface. Some backends are non-atomic by design, e.g.
the X11 backend or the legacy DRM backend.
Updates: https://github.com/swaywm/wlroots/issues/1640
The documentation for wayland-server.h says:
> Use of this header file is discouraged. Prefer including
> wayland-server-core.h instead, which does not include the server protocol
> header and as such only defines the library PI, excluding the deprecated API
> below.
Replacing wayland-server.h with wayland-server-core.h allows us to drop the
WL_HIDE_DEPRECATED declaration.
atomic and legacy now both pass the backend as the user data for the
pageflip event. We than retrieve the correct connector by matching on
the crtc_id passed to the page_flip_handler2.
Wlroots also requires the DRM_CRTC_IN_VBLANK_EVENT capability now.
Fixes#1297
The backend doesn't need to handle transform changes, since everything is done
in software. In fact, all of the implementations were all identical and just
set the transform.
We could add support for hardware transforms, but:
- This would require a different field (something like hardware_transform)
- Not all combinations are possible because there often are hardware
limitations
- The Wayland protocol isn't ready for this (in particular xdg-output, see [1])
This belongs to a different patch series anyway.
[1]: https://patchwork.freedesktop.org/series/52324/
